Ferrari 360 Modena
FERRARI 360 MODENA - SERVICE MANUAL
FERRARI 360 MODENA - SERVICE MANUAL - English Workshop Manual, to Ferrari 360 Modena. INDEX: 0 GENERAL INFORMATION 01 ORGANISATION OF THE MANUAL - 01.01 consulting the manual - 01.02 updating - printing - 01.03 symbols - 01.04 abbreviations and terms with particular meanings 02 GENERAL INFORMATION - 02.01 manual users - 02.02 repairs and maintenance procedures - 02.03 use of original ferrari equipment and spare parts - 02.04 repairs under warranty 03 SAFETY - 03.01 preventive measures and protection devices - 03.02 dangerous parts - 03.03 dangerous emissions and products 04 CAR SPECIFICATIONS - 04.01 identification plates - 04.02 homologation plates - 04.03 instruction plates - 04.04 child airbag-safety system plates 05 SPECIFICATIONS - 05.01 performance and consumption - 05.02 dimensions and weights A REFILLING AND MAINTENANCE A1 REFILLING - a1.01 characteristics of the fluids used - a1.02 refill servicing table A2 PROGRAMMED MAINTENANCE PLAN - a2.01 programmed maintenance plan A3 MAINTENANCE PROCEDURES - a3.01 checking, changing or replacing engine oil and filters - a3.02 checking and changing gearbox-differential oil - a3.03 replacing and checking timing system belt tension - a3.04 checking tension and replacing auxiliary member belts - a3.05 checking and replacing spark plugs - a3.06 checking the window-washer fluid level - a3.07 checking the blow-by system pipes and connections - a3.08 checking the cooling system pipes and connections - a3.09 checking the injection and ignition system pipes and connections - a3.10 replacing the activated carbon filter - a3.11 checking the oil level on the "f1" gearbox - a3.12 replacing the oxygen sensor - a3.13 replacing the air filters - a3.14 replacing the air temperature control system filter - a3.15 checking exhaust system connections - a3.16 checking emission levels - a3.17 tightening of nuts,unions and clamps - a3.18 checking the brake and clutch system fluid levels - a3.19 checking the hydraulic steering fluid level - a3.20 inspecting the braking system - a3.21 checking the service brakes and replacing pads - a3.22 checking operation of the service/parking brakes and control clearance - a3.23 checking the suspension parts - a3.24 checking car alignment - a3.25 inspecting the air temperature control system - a3.26 lubricating and checking hinges and registers - a3.27 checking the fastening and operation of seats and belts - a3.28 checking and recharging the battery - a3.29 checking absorption and re-charging the alternator - a3.30 checking the state of the box-type components and the chassis - a3.31 checking wheels and tires - a3.32 airbag replacement - a3.33 leather interior treatment B ENGINE B1 INTRODUCTION - b1.01 technical features - b1.02 specific equipment - b1.03 tightening torques B2 REMOVING COMPLETE ENGINE ASSEMBLY - b2.01 disassembly - b2.02 re-assembly B3 COMPONENTS - b3.01 timing system driving belts - b3.02 camshafts-timing variators-pulleys - b3.03 cylinder heads - b3.04 oil sump - b3.05 oil pump - b3.06 pistons and connecting rods - b3.07 crankcase covers and supports - b3.08 crankshaft - b3.09 crankase and cylinder liners - b3.10 pressure-tightness test B4 LUBRICATION SYSTEM - b4.01 system outline - b4.02 oil filter - b4.03 oil tank - b4.04 oil radiator - b4.05 oil and gas vapour recirculation B5 COOLING SYSTEM - b5.01 system outline - b5.02 water pump - b5.03 thermostatic valve - b5.04 water radiators - b5.05 expansion tank - b5.06 oil-water heat exchanger - b5.07 filling the system B6 FUEL SUPPLY SYSTEM - b6.01 fuel supply system outline - b6.02 fuel vapour emission outline - b6.03 fuel pump - b6.04 fuel level indicator - b6.05 pressure regulator - b6.06 roll-over shut-off valve - b6.07 fuel tank - b6.08 motor-driven throttle body - b6.09 checking the fuel supply system pressure seal B7 AIR INTAKE AND EXHAUST SYSTEM - b7.01 air intake system outline - b7.02 intake manifold - b7.03 air intake - b7.04 actuating system outline - b7.05 exhaust system outline - b7.06 catalytic converter - b7.07 silencer - b7.08 exhaust manifold C INJECTION-IGNITION C1 SPECIFICATIONS - c1.01 specification - c1.02 system description - c1.03 operating principle C2 SENSORS - c2.01 timing sensor - c2.02 angular velocity sensor - c2.03 air flow meter - c2.04 coolant temperature sensor - c2.05 throttle potentiometer - c2.06 oxygen sensors (lambda sensor) - c2.07 detonation sensor - c2.08 accelerator pedal position sensor - c2.09 tank pressure sensor and vapour interception valve (euro 3 - us version) C3 ACTUATORS - c3.01 fuel pump - c3.02 electro-injectors - c3.03 coil - c3.04 timing variator control solenoid valve - c3.05 exhaust by-pass solenoid valve - c3.06 intake actuation system - c3.07 check engine" or "engine control system faults" and "slow-down" warning lights - c3.08 relays and harness - c3.09 secondary air pump (us m.y. 2000 version) - c3.10 anti-evaporation solenoid valve C4 SIGNALS TO THE ECU - c4.01 air conditioning system engaged - c4.02 catalytic converter temperature - c4.03 car speed - c4.04 key "on" - c4.05 fuel warning light - c4.06 battery voltage - c4.07 alarm system start-up - c4.08 other inlets C5 PROCEDURES - c5.01 replacing the motronic ecu C6 DIAGNOSIS - c6.01 diagnosis with sd-2 tester - c6.02 engine parameters display - c6.03 error signals - c6.04 active diagnosis - c6.05 automatic cycle D CLUTCH-GEARBOX-DIFFERENTIAL D1 GENERAL SPECIFICATIONS - d1.01 technical features - d1.02 specific tooling - d1.03 commercial tooling - d1.04 tightening torques D2 DETACHING THE ENTIRE GEARBOX- DIFFERENTIAL UNIT - d2.01 dismantling - d2.02 re-assembly D3 CLUTCH - d3.01 replacing the components - d3.02 clutch pedal stroke adjustment - d3.03 clutch control hydraulic system - d3.04 system bleeding D4 GEARBOX - d4.01 replacing the external components - d4.02 replacing and adjusting the control cables - d4.03 replacing the gearbox lever housing - d4.04 detaching/re-fitting the gearbox support movable frame - d4.05 gearbox overhaul D5 DIFFERENTIAL - d5.01 replacing the components - d5.02 axle shaft D6 ELECTRONICALLY-CONTROLLED GEARBOX - d6.01 introduction - d6.02 general features - d6.03 transmission control unit (tcu) - d6.04 operation - d6.05 hydraulic system - d6.06 power unit - d6.07 actuators - d6.08 measuring sensors and signal switches - d6.09 signals and controls - d6.10 system functions - d6.11 replacing the electronic control unit (tcu) - d6.12 diagnosis - d6.13 centring the gear shifting-selection actuator lever (finger) E STEERING E1 GENERAL INFORMATION - e1.01 technical features - e1.02 hydraulic system outline - e1.03 tightening torques E2 COMPONENTS - e2.01 hydraulic steering pump - e2.02 steering box - e2.03 hydraulic steering tank - e2.04 cooling coil - e2.05 steering column E3 PROCEDURES - e3.01 filling of the hydraulic steering pump - e3.02 system filling and draining F SUSPENSION SYSTEMS AND WHEELS F1 TECHNICAL FEATURE - f1.01 technical features - f1.02 tightening torques - f1.03 specific equipment F2 COMPONENTS - f2.01 hub-holder-stub axle - f2.02 wheel bearings - f2.03 suspension arms and tie-rods - f2.04 flanblock - ball joints - f2.05 shock absorbers - f2.06 stabilizer bars - f2.07 wheel rims - f2.08 tyres F3 PROCEDURES - f3.01 detaching the entire front suspension - f3.02 detaching the entire rear suspension - f3.03 replacing the front wheel bearing - f3.04 replacing the rear wheel bearing - f3.05 check and adjustment of wheel alignment - f3.06 wheel replacement - f3.07 wheel balancing F4 VARIABLE-SETTING SHOCK ABSORBER ADJUSTMENT SYSTEM - f4.01 system outline - f4.02 system operation - f4.03 system components - f4.04 diagnostcs G BRAKING SYSTEM G1 GENERAL INFORMATION' - g1.01 technical specifications - g1.02 system outline G2 G 2 COMPONENTS - g2.01 servo brake/pump - g2.02 brake fluid tank - g2.03 pedal board - g2.04 brake calipers - g2.05 brake discs - g2.06 hand brake - g2.07 abs/asr electro-hydraulic unit G3 PROCEDURES - g3.01 replacing the service brake calipers - g3.02 filling and draining of the brake system - g3.03 replacing the hand brake pads - g3.04 replacing the hand brake caliper - g3.05 hand brake adjustment - g3.06 foot-brake pedal position adjustment G4 ABS-ASR-EBD-MSR SYSTEMS - g4.01 theory - g4.02 components - g4.03 abs adjustment phases - g4.04 abs adjustment cycle G5 DIAGNOSIS - g5.01 sd-2 tester system - g5.02 abs/asr brake warning lights H INSTRUMENTS AND CONTROLS H1 INSTRUMENTS - h1.01 instrument panel - h1.02 warning lights - h1.03 multi-function display - h1.04 buttons for adjusting functions and instruments - h1.05 diagnosis H2 CONTROLS - h2.01 location in the car - h2.02 ignition switch - h2.03 switches/push-buttons - h2.04 door controls - h2.05 power windows - h2.06 steering wheel - h2.07 steering wheel levers - h2.08 rear view and wing mirrors - h2.09 internal lighting and clock - h2.10 hand brake lever - h2.11 gearshift lever - h2.12 ashtray - cigar lighter - h2.13 opening devices for the engine/luggage compartment lids and for the fuel tank flap - h2.14 seat control - h2.15 stereo system - h2.16 accelerator control H3 SAFETY SYSTEMS - h3.01 alarm system - h3.02 airbag - h3.03 seatbelts - h3.04 inertia switch - h3.05 fire extinguisher (optional) H4 DRIVING THE CAR - h4.01 breaking-in - h4.02 engine ignition and gear shifting (mechanical gearbox) - h4.03 engine ignition and gear shifting (electrically-controlled gearbox) I AIR CONDITIONING I1 SYSTEM - i1.01 system outline - i1.02 operation - i1.03 controls I2 COMPONENTS - i2.01 compressor - i2.02 condenser - i2.03 dehydrator filter - i2.04 pressure switch - i2.05 expansion valve - i2.06 heater/evaporator - i2.07 proportional valve (tgk) - i2.08 recirculation pump - i2.09 ntc sensors - i2.10 electronic climate control unit - i2.11 relays and fuses I3 SYSTEM MAINTENANCE PROCEDURES - i3.01 system draining - i3.02 system filling I4 CHECKS - i4.01 sd-2 operation check - i4.02 compressor oil level check and filling - i4.03 expansion valves check - i4.04 pressure switch control - i4.05 electric fan activation control L ELECTRICAL SYSTEM L1 GENERAL INFORMATION - l1.01 specifications - l1.02 key-operated circuits - l1.03 lights L2 COMPONENTS - l2.01 battery - l2.02 master battery switch - l2.03 generator - l2.04 starter motor - l2.05 windscreen wiper motor - l2.06 head lights - l2.07 rear lights - l2.08 side indicators - l2.09 ecus - l2.10 fuses and relays boxes - l2.11 horn - l2.12 diagnosis tester plug-in L3 OPERATIONS AND CHECKS - l3.01 checking the electrical system absorption - l3.02 checking the battery charge level - l3.03 recharging the battery - l3.04 headlight aiming M BODYWORK PARTS M1 GENERAL INFORMATION - m1.01 tightening torques M2 OUTSIDE PARTS - m2.01 engine compartment lid - m2.02 luggage compartment lid - m2.03 front bumper - m2.04 rear bumper - m2.05 wheelhouse - m2.06 windscreen - m2.07 windscreen wiper - m2.08 windscreen washer - m2.09 rear window - m2.10 quarter windows - m2.11 doors - m2.12 underfloor parts - m2.13 engine compartment shields - m2.14 headlight washer (optional) - m2.15 rear light support covering - m2.16 fuel tank filler neck - m2.17 fuel tank cap flap - m2.18 door ring strips and covering - m2.19 removable sunroof (optional) M3 INTERNAL COMPONENTS - m3.01 dashboard - m3.02 tunnel - m3.03 seats - m3.04 passenger compartment and roof lining - m3.05 engine inspection lid - m3.06 luggage compartment lining M4 PAINTING - m4.01 re-painting cycles at the workshop - m4.02 touch-up technologies - m4.03 preparation and painting of bumpers with "smc" technique - m4.04 painting
Ferrari 360 Modena - Service Manual / Workshop Manual
inicio - index
coche - car
moto
4x4
quad - buggy
cami?n - truck
e-mail
utilizamos cookies propias y de terceros para obtener datos estadisticos de la navegacion de nuestros usuarios y mejorar nuestros servicios, si continua usando este sitio, asumiremos que est? de acuerdo con ello.