Ferrari 360 Challenge Stradale - Workshop Manual
ferrari 360 challenge stradale
WORKSHOP MANUAL
FERRARI 360 CHALLENGE STRADALE - WORKSHOP, SERVICE, REPAIR MANUAL - English Workshop Manual to vehicles Ferrari 360 Challenge Stradale. CONTENTS: 0 GENERAL INFORMATION - 01 ORGANISATION OF THE MANUAL - 01.01 consulting the manual - 01.02 updating - print - 01.03 symbols - 01.04 abbreviations and special terms - 02 GENERAL INFORMATION - 02.01 user of the manual - 02.02 service procedures - 02.03 use of original tools and spare parts - 02.04 guarantee repairs - 02.05 tightening torques - 03 SAFETY - 03.01 prevention measures and protection devices - 03.02 dangerous parts - 03.03 dangerous products and emissions - 04 CAR SPECIFICATIONS - 04.01 identification data - 04.02 homologation plates - 04.03 instruction plates - 04.04 child airbag-safety system plates - 05 SPECIFICATIONS - 05.01 performance and consumption - 05.02 dimensions and weights A REFILLING AND MAINTENANCE - A1 REFILLING - a1.01 characteristics of the fluids used - a1.02 refill servicing tableservicing table - A2 PROGRAMMED MAINTENANCE PLAN - a2.01 programmed maintenance plan - A3 MAINTENANCE PROCEDURES - a3.01 checking, changing or replacing engine oil and filters - a3.02 checking and changing gearbox-differential oil - a3.03 replacing and checking timing system belt tension - a3.04 checking tension and replacing auxiliary member belts - a3.05 checking and and replacing spark plugs - a3.06 checking the window-washer fluid level - a3.07 checking the the blow-by system pipes and connections - a3.08 checking the the cooling system pipes and connections - a3.09 checking the injection and ignition system pipes and connections - a3.10 replacing the activated carbon filter - a3.11 checking the oil level on the f1 gearbox - a3.12 replacing the oxygen sensor - a3.13 replacing the air filters - a3.14 replacing the the air temperature control system filter - a3.15 checking exhaust exhaust system connections - a3.16 checking emission levels - a3.17 tightening of nuts, unions and clamps - a3.18 checking the brake system fluid levels - a3.19 checking the hydraulic steering fluid level - a3.20 inspecting the the braking system - a3.21 checking the the service brakes and replacing pads - a3.22 checking operation of the service parking brakes and control clearance - a3.23 checking the the suspension parts - a3.24 checking car alignment - a3.25 inspecting the air temperature control system - a3.26 lubricating and checking hinges registers - a3.27 checking the fastening and operation of seats and belts - a3.28 checking and recharging the battery - a3.29 checking absorption and re-charging the alternator - a3.30 checking the state of the box-type components and the chassis - a3.31 checking wheels and tires - a3.32 airbag replacement - a3.33 leather interior treatment B ENGINE - B1 INTRODUCTION - b1.01 technical features - b1.02 specific equipmentequipment - b1.03 tightening torques - B2 REMOVING COMPLETE ENGINE ASSEMBLY - b2.01 disassembly - b2.02 re-assembly - B3 COMPONENTS - b3.01 timing system driving belts - b3.02 camshafts-timing variators-pulleys - b3.03 cylinder heads - b3.04 oil sump - b3.05 oil pump - b3.06 pistons and connecting rods - b3.07 crankcase covers and supports - b3.08 crankshaft - b3.09 crankase and cylinder liners - b3.10 pressure-tightness test - B4 LUBRICATION SYSTEM - b4.01 system outline - b4.02 oil filter - b4.03 oil tank - b4.04 oil radiator - b4.05 oil and gas vapour recirculation - B5 COOLING SYSTEM - b5.01 system outline - b5.02 water pump - b5.03 thermostatic valve - b5.04 water radiators - b5.05 expansion tank - b5.06 oil-water heat exchanger - b5.07 filling the system - B6 FUEL SUPPLY SYSTEM - b6.01 fuel supply system outline - b6.02 fuel vapour emission outline - b6.03 fuel pump unit - b6.04 fuel level indicator - b6.05 pressure regulator - b6.06 roll-over shut-off valve - b6.07 fuel tank - b6.08 motor-driven throttle body - b6.09 checking thefuel supply system pressure seal - B7 AIR INTAKE AND EXHAUST SYSTEM - b7.01 air intake system outline - b7.02 intake manifold - b7.03 air intake - b7.04 outline of the pneumatic actuating system - b7.05 exhaust system outline - b7.06 catalytic converter - b7.07 silencer - b7.08 exhaust manifold C INJECTION-IGNITION - C1 SPECIFICATIONS - c1.01 specifications - c1.02 system description - C2 SENSORS - c2.01 timing sensor - c2.02 angular velocity sensor - c2.03 air flow meter - c2.04 coolant temperature sensor - c2.05 throttle potentiometer - c2.06 oxygen sensors (lambda sensor) - c2.07 detonation sensor - c2.08 accelerator pedal position sensor - c2.09 tank pressure sensor and vapour interception valve - C3 ACTUATORS - c3.01 fuel pump - c3.02 electro-injectors - c3.03 coil - c3.04 timing variator control solenoid valve - c3.05 exhaust by-pass solenoid valve - c3.06 pneumatic actuation system solenoid valves - c3.07 anti-evaporation solenoid valve - c3.08 secondary air pump (us version) - C4 PROCEDURES - c4.01 replacing the motronic ecu D CLUTCH - GEARBOX - DIFFERENTIAL - D1 GENERAL SPECIFICATIONS - d1.01 technical features - d1.02 specific tooling - d1.03 tightening torques - D2 DETACHING THE ENTIRE GEARBOX- DIFFERENTIAL UNIT - d2.01 dismantling - d2.02 re-assembly - D3 CLUTCH - d3.01 replacing the components - d3.02 system bleeding - d3.03 clutch control hydraulic system - D4 GEARBOX - d4.01 replacing the external components - d4.02 detaching re-fitting the gearbox support movable frame - d4.03 gearbox overhaul - D5 DIFFERENTIAL - AXLE SHAFTS - d5.01 component replacement - d5.02 axle shaft - D6 ELECTRONICALLY-CONTROLLED GEARBOX - d6.01 introduction - d6.02 general features - d6.03 replacing the the electronic control unit (tcu) - d6.04 operation - d6.05 hydraulic system - d6.06 power unit - d6.07 actuators - d6.08 measuring sensors and signal switches - d6.09 signals and controls - d6.10 centring the gear shifting-selection actuator lever (finger) E STEERING - E1 GENERAL INFORMATION - e1.01 technical features - e1.02 hydraulic system outline - e1.03 tightening torques - E2 COMPONENTS - e2.01 hydraulic steering pump - e2.02 steering box - e2.03 hydraulic steering tank - e2.04 cooling coil - e2.05 steering column - E3 PROCEDURES - e3.01 filling of the hydraulic steering pump - e3.02 system filling and draining F SUSPENSION SYSTEMS AND WHEELS - F1 TECHNICAL FEATURE - f1.01 technical features - f1.02 tightening torques - f1.03 specific equipment - F2 COMPONENTS - f2.01 hub-holder-stub axle - f2.02 wheel bearings - f2.03 suspension arms and tie-rods - f2.04 flamblock - ball joints - f2.05 shock absorbers - f2.06 stabilizer bars - f2.07 wheel rims - f2.08 tyres - F3 PROCEDURES - f3.01 detaching the entire front suspension - f3.02 detaching the entire rear suspension - f3.03 replacing the front wheel bearing - f3.04 replacing the rear wheel bearing - f3.05 check and adjustment of wheel alignment - f3.06 wheel replacement - f3.07 wheel balancing - F4 VARIABLE-SETTING SHOCK ABSORBER ADJUSTMENT SYSTEM - f4.01 system - f4.02 system components G BRAKING SYSTEM - G1 GENERAL INFORMATION - g1.01 technical specifications - g1.02 system outline - g1.03 tightening torques - G2 COMPONENTS - g2.01 servo brake pump - g2.02 brake fluid tank - g2.03 pedal board - g2.04 brake calipers - g2.05 brake discs - g2.06 hand brake - g2.07 abs asr electro-hydraulic unit - G3 PROCEDURES - g3.01 replacing the service brake calipers - g3.02 filling and draining of the brake system - g3.03 replacing the hand brake pads - g3.04 replacing the hand brake caliper - g3.05 hand brake adjustment - g3.06 adjusting the brake pedal and brake switch position H INSTRUMENTS AND CONTROLS - H1 INSTRUMENTS - h1.01 instrument panel - h1.02 warning lights - h1.03 multi-function display - h1.04 buttons for adjusting functions and instruments - H2 CONTROLS - h2.01 location in the car - h2.02 ignition switch - h2.03 switches push-buttons - h2.04 door controls - h2.05 power windows - h2.06 steering wheel - h2.07 steering wheel levers - h2.08 rear view and wing mirrors - h2.09 internal lighting and clock - h2.10 hand brake lever - h2.11 gearshift lever - h2.12 accelerator control - h2.13 opening devices for the engine luggage compartment lids and for the fuel tank - h2.14 seat control - h2.15 stereo system - H3 SAFETY SYSTEMS - h3.01 alarm system - h3.02 airbag - h3.03 seatbelts - h3.04 inertia switch - h3.05 extinguisher (optional) I AIR CONDITIONING - I1 SYSTEM - i1.01 system outline - i1.02 controls - i1.03 tightening torques - I2 COMPONENTS - i2.01 compressor - i2.02 condenser - i2.03 dehydrator filter - i2.04 pressure switch - i2.05 expansion valve - i2.06 heater evaporator - i2.07 proportional valve (tgk) - i2.08 recirculation pump - i2.09 sensors - i2.10 electronic climate control unit - I3 SYSTEM MAINTENANCE PROCEDURES - i3.01 system draining - i3.02 system filling L ELECTRICAL SYSTEM - L1 GENERAL INFORMATION - l1.01 specifications - l1.02 key-operated circuits - l1.03 lights - l1.04 tightening torques - L2 COMPONENTS - l2.01 battery - l2.02 master battery switch - l2.03 generator - l2.04 starter motor - l2.05 windscreen wiper motor - l2.06 head lights - l2.07 rear lights - l2.08 side indicators - l2.09 ecus - l2.10 fuses and relays boxes - l2.11 horn - l2.12 diagnosis tester plug-in - L3 OPERATIONS AND CHECKS - l3.01 checking the electrical system absorption - l3.02 checking the battery charge level - l3.03 recharging the battery - l3.04 headlight aiming M BODYWORK PARTS - M1 GENERAL INFORMATION - m1.01 tightening torques - M2 OUTSIDE PARTS - m2.01 engine compartment lid - m2.02 luggage compartment lid - m2.03 front bumper - m2.04 rear bumper - m2.05 wheelhouse - m2.06 windscreen - m2.07 windscreen wipers - m2.08 windscreen washer - m2.09 rear window - m2.10 quarter windows - m2.11 doors - m2.12 underfloor parts - m2.13 engine compartment guards - m2.14 headlight washers (optional) - m2.15 rear light support covering - m2.16 fuel tank filler neck - m2.17 fuel tank cap flap - m2.18 door ring strips and covering - m2.19 fixed lexan window with sliding unit (optional) - M3 INTERNAL COMPONENTS - m3.01 dashboard - m3.02 tunnel - m3.03 seats - m3.04 passenger compartment and roof lining - m3.05 engine inspection lid - m3.06 luggage compartment lining - M4 PAINTING - m4.01 re-painting cycles at the workshop - m4.02 touch-up technologies - m4.03 preparation and painting of bumpers with smc technique - m4.04 painting - m4.05 applying the tricolour adhesive strip
Ferrari 360 Challenge Stradale - Workshop Manual
inicio - index
coche - car
moto
4x4
quad - buggy
cami?n - truck
e-mail