Iveco Eurocargo Tector 12/26t
IVECO EUROCARGO TECTOR 12/26T - WORKSHOP, SERVICE, REPAIR MANUAL
IVECO EUROCARGO TECTOR 12/26T - WORKSHOP, SERVICE, REPAIR MANUAL - English Workshop Manual, to vehicles Iveco Eurocargo Tector 12/26t. CONTENTS: SECTION 1 - GENERAL SPECIFICATIONS General specifications - Composition of the models - Identification data and location on vehicle - Filling up - International lubricant designation SECTION 2 - ENGINE Engine - Engine identification codes - Main servicing operations to be performed on engine fitted on vehicle - Warnings - Engine removal-refitting - Injectors replacement - Replacing seal ring front cover driving shaft - Replacing seal ring flywheel housing box - Cylinder head rem oval/refitting - Engine f4 ae 0481 - Engine f4 ae 0681 - Troubleshooting guide SECTION 3 - CLUTCH Clutch - Description - Specifications and data - Diagnostics - Tightening torques - Tools - Removal and refitting - Driven plate overhaul - Bleeding air from clutch circuit - Thrust bearing removal - refitting - Replacing clutch shaft support bearing - Hydraulic control - Wear indicator refitting and adjustment (15/16” clutches) - Adjusting operating cylinder push rod (new 15/16” clutch) - Checking and adjusting the clutch pedal (14” - 13”/14” clutches) - Checking and adjusting the clutch pedal (15”/16” clutches) SECTION 4 - GEARBOX Gearbox - Diagnostics - Gearbox 2855.6 - Gearbox 2865.6 - Gearbox 2870.9 - Gearbox 2895.9 - Allison gearbox md 3060p - Gearbox eaton fso 5206b SECTION 5 - PROPELLER SHAFTS Propeller shafts - Description - Propeller shaft layout on vehicles - Propeller shaft specifications and data - Diagnostics - Tightening torques - Sliding propeller shaft removal-refitting - Fixed propeller shaft removal- refitting - Checking propeller shafts on vehicle SECTION 6 - REAR AXLES Rear axles - Axles in tandem meritor sp 145 e - Disconnection - Reconnection - Checking wheel hub components - Dismantling inter-axle unit - Checking inter-axle unit components - Fitting inter-axle unit - Adjusting drive input shaft bearing end float - Adjusting differential lock and inter-axle control pin end-stop - Dismantling gear cage - Checking differential components - Assembling gear cage - Calculating bevel pinion position in differential casing - Adjusting the cap gap - Removing differential lock - Dismantling differential casing - Dismantling gear cage - Dismantling bevel pinion support - Checking differential components - Assembling gear cage - Specimen calculations - Assembling differential casing SECTION 7 - FRONT AXLES Front axles - Front axle 5845 - Front axles 5842/5 - 5851/5 - Front axle 5871/5 SECTION 8 - SUSPENSIONS Suspensions - Front and rear mechanical suspensions - Front and rear pneumatic suspensions SECTION 9 - WHEELS AND TIRES Wheels and tires - Description - Specifications and data - Tools - Diagnostics - Static wheels balancing - Correction of residual static unbalance - Tire pressure - Tire behaviour depending on pressure SECTION 10 - STEERING Steering - Description - Specifications and data - Diagnostics - Tightening torques - Tools - Zf hydraulic power steering (8095-8098) - Hydraulic power steering disconnection and reconnection (zf 8095-8098) - Hydraulic steering limiter adjustment - Trw tas 55 hydraulic power steering - Hydraulic steering limitation - Hydraulic power steering disconnection and reconnection (trw tas 55) - Air drain from hydraulic power steering circuit - Measure of drive case clearances detected on steering wheel - Maximum pressure check in hydraulic power steering system SECTION 11 - PNEUMATIC SYSTEM - BRAKES Pneumatic system - brakes - Graphic symbols for hydropneumatic systems diagrams (miscellaneous and generators) - Graphic symbols for hydropneumatic systems diagrams (valves) - Graphic symbols for hydropneumatic systems diagrams (tanks and accumulators) - Graphic symbols for hydropneumatic systems diagrams (converters, cylinders and calipers) - Graphic symbols for hydropneumatic systems diagrams (cylinders and calipers) - Graphic symbols for hydropneumatic systems diagrams (coupling half-joints and heads) - Graphic symbols for hydropneumatic systems diagrams (signaling devices and switches) - Graphic symbols for hydropneumatic systems diagrams (brakes) - Pipings and fittings - Braking system - Arrangement on a vehicle of main braking system components - Description - Brakes - Diagnostic - Tightening torques - Tools - Specifications and data - pneumatic system - Specifications and data - brakes - Checks of main brake system components - Main brake system components - Compressor - A.p.u. (air processing unit) - Engine brake switch - Engine brake solenoid valve - Engine brake control operating cylinder - Manual discharge valve - Safety valve (optional) - Duplex distributor - Pressure relief valve - Relay valve - Check valve - Parking brake control manual distributor (single vehicles) - Parking brake control manual distributor (vehicles adapted for towing) - Quick discharge valve - Triple control servodistributor - Coupling heads - Pressure plug valve - Membrane brake cylinder (for disc brakes and drum brakes) - Combined brake cylinder - Abs systemwith ebl function - Electronic unit - Revolutions sensors - Phonic wheels - Electro-pneumatic valve - Brake repairs models ml 110 el.. / 120 el..) - Brake calipers revision - Brake discs revision - Brake repairing - Checks - Rear brakes revision - Brake calipers revision types b6 - Brake caliper overhaul type sn6-sn7 - Rear disc brakes revision (12-18 t) - Brake discs revision - Brake discs turning and grinding - Rear drum brakes - model 260e28ke - Rear brakes revision (26 t) - Drum turning - Braking gaskets replacement - Braking gaskets turning SECTION 12 - BODY - CHASSIS Body - chassis - Cab - Protective body treatments - Checking the geometry of the chassis frame - General rules forworking on the chassis frame - Precautions - Chassis frame - Repairs and checks - Chassis reference dimensions - Cab geometry - Seal application diagram - Cab anchoringcab anchoring and tightening torques - Tools - Repairs - Hydraulic cab lifting system - Replacing windscreen window - Instrument panel - Middle instrument panel - Instrument panel covering - Heating and ventilation SECTION 13 - SERVICE PLAN Service plan - Servicing - Service frequency - Extra plan operations - Scheduled maintenance operations - Extra-plan operations - Scheduled maintenance operations - Extra-plan operations - M1 service - M2 service - M3 service - Extra-plan maintenance - Ep1 service - Ep2 service - Ep3 service - Ep4 service - Ep5 service
Iveco Eurocargo Tector 12/26t - Repair, Service and Maintenance Manual
inicio - index
coche - car
moto
4x4
quad - buggy
camión - truck
e-mail